How to Replace Wiper Blades Step by Step: The Step Most People Skip
Replacing wiper blades is often considered one of the easiest jobs on a car: remove the old blade, fit the new one, and you are done. On older cars, it really can be that simple. On many newer models, however, the wipers park beneath the rear edge of the bonnet. Lifting a wiper arm from that position can make it hit the bodywork and damage the paint. And if an arm without its blade slips out of your hand, it can even crack the windscreen.
The instructions on wiper blade packaging rarely mention this because they have to cover hundreds of different car models. So we will start with the step most people skip.
Myth: “You Just Lift the Wiper Arm”
On cars whose wipers park beneath the edge of the bonnet, the arms cannot be lifted freely away from the glass while in their resting position. That is why manufacturers provide a service position (sometimes also called the winter position): the wipers move higher up the windscreen, where the arms can be lifted without touching the bonnet. Mercedes-Benz specifically states in its owner’s manuals that the arms should only be raised from the vertical position to avoid damaging the bonnet.
If your wiper blades are fully visible and the arms can be lifted without resistance, you probably do not need to activate a service position. If the wipers are hidden beneath the bonnet, do not lift them until you have activated it.
How to Activate It: Examples from Owner’s Manuals
The examples below show just how much the procedures can vary. They are not universal instructions: the method can differ not only between makes but also between models and generations of the same make.
• Volkswagen Polo (fifth generation): within ten seconds of switching off the ignition, press the wiper stalk down to the single-wipe position.
• BMW 7 Series (E65/E66 generation): after switching off the ignition, move the wiper stalk upwards past the resistance point and hold it there for approximately three seconds.
• Mercedes-Benz S-Class and CLS from the 2000s, with a key: turn the key to position 1 and switch on the wipers. When the wiper arms reach the vertical position, turn the key back to position 0.
• Volvo XC40, XC90 and newer generations of the S60: activate the service position on the central display using the Wiper Service Position function.
On newer models from the same manufacturer, the procedure may be completely different—for example, where the wiper controls have been moved to the indicator stalk or into an on-screen menu.
If the procedure on your car differs from the examples above, do not try to force the wipers into position. Consult the manufacturer’s instructions for your exact model and model year.
Return the wipers from their service position before driving, following the procedure in your vehicle’s manual. In winter, check that the blades are not frozen to the glass before activating the service position. Volvo, for example, explicitly warns about this in its owner’s manuals.
When to Replace Wiper Blades and How to Choose the Right Ones
A wiper blade should be replaced if it leaves streaks, judders or squeaks, misses an area within your field of vision, or has visibly cracked rubber. We have covered the signs of wear in more detail in our article Icy Windscreens and Wipers in Winter: What Really Helps and What Causes Damage. There is no single replacement interval: six to twelve months is commonly suggested, and Mercedes-Benz recommends replacement twice a year—spring and autumn—for some models. A worn blade can eventually scratch the glass as well.
Length
On many cars, the driver’s and passenger’s front wiper blades are different lengths, while the rear blade is a separate matter. Look up the correct sizes in your vehicle’s manual or in a wiper blade manufacturer’s catalogue for your model, or measure the existing blade from one end of the rubber to the other. A blade that is “roughly the right length” may leave part of the glass unwiped or strike the edge of the windscreen.
Blade Type
Conventional framed blades are less expensive and work well when they are the correct size. Frameless blades (also called flat or aero blades) contain a steel strip that distributes pressure along the rubber and have no exposed frame in which snow and ice can collect. Hybrid blades have a frame covered by a plastic housing and sit somewhere between the other two types.
Connector Type
This is where people most often make a mistake. The blade attaches to the wiper arm through a connector, and there are several types: J-hook or U-hook, side pin, top-lock or push-button connectors, bayonet fittings and others. Universal blades come with a set of adapters, but no single kit fits absolutely every connector type.
Practical tip: before buying, take a photo of the connection between the old blade and the wiper arm. Show it to the retailer or compare it with the illustrations on the packaging.
Replacing the Front Wiper Blades Step by Step
1. Check your vehicle’s manual to see whether your car has a wiper service position and how to activate it.
2. Activate the service position if required. On some cars the ignition must be on; on others, the position is activated after switching the ignition off, following a specific sequence. The bonnet must be fully closed.
3. Switch off the ignition and remove the key, or switch off the system in a keyless vehicle, to prevent the wipers from moving unexpectedly. Manufacturers also warn about this risk in their manuals.
4. Place a folded towel or a piece of cardboard on the glass beneath the wiper arm. The arm is spring-loaded and can crack the glass if it slips out of your hand without a blade attached.
5. Lift the arm away from the windscreen until it can stay raised by itself. Do not force it any further.
6. Release the old blade’s connector using the method designed for that fitting: a tab, button, cover or release from a hook. If you are unsure, consult the instructions supplied with the new blade.
7. Remove the old blade by holding its connector. Do not pull on the rubber, as it may tear.
8. Compare the new blade with the old one for both length and connector type. If necessary, fit the appropriate adapter supplied in the package.
9. Fit the new blade according to the blade manufacturer’s instructions and make sure the connection is properly locked by giving the blade a gentle pull.
10. Hold the arm securely and lower it slowly onto the glass, then repeat the process on the other side.
11. Before switching the wipers on or driving away, make sure both arms are fully lowered onto the glass. Volvo specifically warns that wiper arms lifted into the service position must be returned to the windscreen before activating wiping, washing or the rain sensor, and before driving, to avoid scratching the paint on the bonnet. Only then should you return the wipers from their service position as instructed in the vehicle’s manual and test them using the washer fluid.
Tip: replace one blade at a time. With the second blade still in place, you have a reference for the connector’s orientation and how it was fitted.
Rear Wiper Blade
The rear wiper blade is shorter and often uses a different connector. Its arm usually cannot be lifted as far away from the glass as a front wiper arm, so do not force it. On some models, the rear blade is sold together with the arm; check the parts catalogue for your vehicle before buying.
Not sure which wiper blades fit your car?
Find a service centre on AutoKonekt that can inspect your wiper system and help you choose and fit the correct blades.
→ Find a service centre on autokonekt.rs
Five Costly Mistakes to Avoid
1. Letting a bare wiper arm snap back onto the glass. The costliest mistake of all: a cracked windscreen instead of a new wiper blade.
2. Lifting concealed wipers without using the service position. The result can be a scratched bonnet or a bent wiper arm.
3. Moving the wiper arm across the glass by hand. Manufacturers such as Mazda warn against manually moving the arm across the windscreen because it may damage wiper components.
4. Failing to lock the blade securely into place. It could come off while driving, leaving the bare arm scraping against the glass.
5. Buying a blade that is “close enough”. The wrong length or a loose-fitting adapter can leave you with a blade that never wipes properly.
When the Problem Is Not the Wiper Blade
If a new blade still leaves streaks or judders, or the wipers do not work properly, the cause may lie elsewhere:
• Greasy or dirty glass. Car-wash wax, tree sap and a build-up of dirt can interfere with even the best blades. Clean the windscreen and the blade rubber, then try again.
• A bent wiper arm or weakened spring. The blade may not make full contact with the glass, leaving an unwiped strip even when the blade is brand-new.
• Wipers that move slowly, stop halfway or fail to return to their parked position. This may indicate a problem with the motor, linkage or wiper control system and should be checked by a service centre.
• Weak or no washer spray. Possible causes include the pump, hose or blocked nozzles, or frozen washer fluid in winter. Read more about winter washer fluid in our article Icy Windscreens and Wipers in Winter.
• Scratches within the swept area of the windscreen. These can be caused by worn blades or by a bare wiper arm scraping the glass. If they affect visibility, have the glass inspected by an automotive glass specialist. On vehicles with an ADAS camera mounted behind the windscreen, camera calibration may be required after glass replacement, in accordance with the vehicle manufacturer’s procedure. Read more in our article [LINK: windscreen replacement and ADAS calibration].
Are your wipers still not working properly after replacement?
On AutoKonekt, find a service centre that can inspect your wiper and washer systems and help resolve the problem—or an automotive glass specialist if the windscreen is damaged.
→ Find a service centre near you: autokonekt.rs/lokacije
What the Regulations Say About Windscreen Wipers
Serbia’s Road Traffic Safety Law requires vehicle owners to ensure that vehicles used on public roads are roadworthy. Article 73 of the Rulebook on the Classification of Motor Vehicles and Trailers and the Technical Requirements for Vehicles in Road Traffic stipulates that windscreen wipers must be installed and designed to operate reliably and wipe the largest possible area of the windscreen in all weather conditions. Article 74 further requires vehicles equipped with wipers to have windscreen washers. Properly functioning wipers are therefore part of a car’s roadworthiness—not merely a matter of comfort.
Frequently Asked Questions
How often should wiper blades be replaced?
Six to twelve months is a commonly recommended interval, depending on climate and use. Check the blades before every winter and replace them as soon as they begin leaving streaks, juddering or squeaking.
What is the wiper service position?
It is a position in which the wipers move higher up the windscreen so their arms can be lifted without hitting the bonnet. The activation procedure varies by make, model and model year; the correct method is explained in your vehicle’s manual.
Can I replace just the rubber insert instead of the whole blade?
Replacement rubber inserts are available separately for some conventional framed blades. With most modern blades, particularly frameless ones, the entire blade is replaced.
Are frameless blades better than conventional ones?
They tend to follow the curve of the windscreen more evenly and have no exposed metal frame in which snow and ice can collect. Conventional blades cost less and can work perfectly well if they are the correct size and replaced regularly. What matters more than the type is that the blade fits the vehicle and is not worn out.
Sources
The service-position procedures described above are based on manufacturers’ owner’s manuals and service documentation for the vehicles mentioned. Publicly available official sources include:
• Volvo Cars Support: Wiper Blade Service Position (S60)
• Volvo Cars Support: Wiper Blade Service Position (XC40)
Mazda MX-5 Owner’s Manual: Replacing Windscreen Wiper Blades



